Crest Electronics CDVS-7000 Manual de usuario Pagina 165
- Pagina / 341
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
User Manual
i Series / iX Series 151
This section of the manual covers operation of the –160 option using the CIGui32 program.
Version 1.26 or higher of the CIGui32 program is required. The CIGui32 program is supplied with
all iX systems free of charge on CD ROM CIC496. It can also be downloaded from the California
Instruments web site (www.calinst.com).
The information provided in this user manual is aimed at guiding the operator in the use of the
160 option through the use of the CIGui32 program. Much of the same information can be found
in the on-line help system of the CIGUI32.
This manual is not intended to elaborate on the intent or purpose of the immunity tests and the
expected behavior of the EUT as described in the RTCA/DO-160 documents. It is assumed that
the end-user is familiar with the content of the RTCA/DO-160 test standard.
9.1.2.2 Test Coverage
The comprehensiveness of the tests that can be performed with the –160 option is determined
primarily by the capabilities of the power source used. Tests that are outside the hardware
capabilities of the power source used will not be enabled and cannot be selected. For these
tests, additional equipment may be required as indicated. The extent of coverage of the –160
option as implemented on the iX Series platform is shown in the table below. Tests marked with
an „x‟ generally require additional hardware to be used. Tests marked „N/A‟ are not applicable to
the corresponding table. Tests marked with a „ ‟ are covered by the –160 option. Tests marked
with a „P‟ are limited in scope and may require additional equipment to perform completely.
No.
115V Tests
Description
Table
A(CF)
Table
A(NF)
Table
A(WF)
No.
28 VDC Tests
Description
Table
ADC
Table
BDC
Table
ZDC
16.5.1.1
Voltage and
Frequency
16.6.1.1
Voltage
16.5.1.2
Voltage Modulation
16.6.1.2
Ripple Voltage
P
P
P
16.5.1.3
Frequency
Modulation
16.6.1.3
Momentary Power
Interruptions
16.5.1.4
Momentary Power
Interruptions
16.6.1.4
Normal Surge
Voltage
16.5.1.5.1
Normal Surge
Voltage
16.6.1.5
Engine Starting
Under Voltage
N/A
16.5.1.5.2
Normal Frequency
Transients
N/A
N/A
16.6.2.1
Abnormal Voltage
16.5.1.6
Normal Frequency
Variations
N/A
16.6.2.2
Low Voltage
Conditions
N/A
N/A
16.5.1.7
Voltage DC
Content
16.6.2.3
Momentary Under
Voltage Operation
16.5.1.8
Voltage Distortion
P
P
P
16.6.2.4
Abnormal Voltage
Surge
16.5.2.1
Abnormal Voltage
and Frequency
16.5.2.2
Momentary Under
Voltage Operation
16.5.2.3.1
Abnormal Surge
Voltage
16.5.2.3.2
Abnormal
Frequency
Transient
N/A
N/A
Table 9-17: -160 Option Test Coverage, 115VAC and 28VDC
- AC Power Source 1
- User Manual 1
- SAFETY SYMBOLS 7
- 1. Introduction 15
- 2. Specifications 16
- 2.2 Mechanical 24
- 2.3 Environmental 24
- 2.4 Regulatory 26
- 2.5 Front Panel Controls 26
- 3.1 Unpacking 29
- 3.2 Power Requirements 29
- 3.3 Mechanical Installation 30
- 3.4 Input Wiring – TB1 30
- 3.6 Connectors - Rear Panel 32
- Description 33
- Centronics 36
- Connector 36
- > 400 uS 36
- 24 i Series / iX Series 38
- 3.8 Output Voltage Ranges 40
- 3.9 Functional Test 41
- 28 i Series / iX Series 42
- 30 i Series / iX Series 44
- 34 i Series / iX Series 48
- 4. Front Panel Operation 51
- FUNCTION 53
- 4.2 Menu Structure 56
- 44 i Series / iX Series 58
- 4.2.2 Overview of Menu 1 58
- 4.3 Output Programming 91
- 4.5 Standard Measurements 97
- 4.7 Transient Programming 108
- 5. Principle of Operation 115
- 5.2 Overall Description 116
- 5.3 Oscillator Assembly 116
- 104 i Series / iX Series 118
- 5.4 Current Limit Board 119
- 5.5 Auxiliary Power Supply 119
- 5.6 DC-DC Power Converter 120
- 5.7 AC Control Logic 120
- 108 i Series / iX Series 122
- 5.8 AC Power Board 123
- 5.9 Input/Output Board 123
- 110 i Series / iX Series 124
- CAUTION 126
- 6. Calibration 127
- 118 i Series / iX Series 132
- 6.6 Non-Routine Calibration 134
- 124 i Series / iX Series 138
- 7. Service 139
- 9. Options 147
- 138 i Series / iX Series 152
- Refer to 157
- 158 i Series / iX Series 172
- 9.1.2.8 160 Test Selection 172
- 164 i Series / iX Series 178
- 168 i Series / iX Series 182
- 170 i Series / iX Series 184
- 172 i Series / iX Series 186
- 174 i Series / iX Series 188
- 176 i Series / iX Series 190
- 178 i Series / iX Series 192
- 9.2 IEC 61000-4-11 Option 194
- 9.3 IEC 61000-4-13 Option 201
- 196 i Series / iX Series 210
- 9.4 EOS Option 213
- 206 i Series / iX Series 220
- 208 i Series / iX Series 222
- Figure 9-39: 15003iX/3-EOS3 222
- 9.5 Mode iX Option 228
- 218 i Series / iX Series 232
- 9.6 Omni Options 236
- 226 i Series / iX Series 240
- 228 i Series / iX Series 242
- Power Switch and Lamp 244
- 80-250V SYNC INPUT FROM iX 250
- SOURCE INPUT,OR 250
- OTHER AC LINE VOLTAGE 250
- 9.8.2.8 704 Test Selection 273
- 260 i Series / iX Series 274
- 262 i Series / iX Series 276
- 266 i Series / iX Series 280
- 268 i Series / iX Series 282
- 270 i Series / iX Series 284
- 272 i Series / iX Series 286
- 274 i Series / iX Series 288
- 276 i Series / iX Series 290
- 278 i Series / iX Series 292
- 280 i Series / iX Series 294
- 282 i Series / iX Series 296
- 284 i Series / iX Series 298
- 286 i Series / iX Series 300
- 9.9.7 ABD Test Selection 309
- 296 i Series / iX Series 310
- 298 i Series / iX Series 312
- 302 i Series / iX Series 316
- Controls 319
- 308 i Series / iX Series 322
- 310 i Series / iX Series 324
- 312 i Series / iX Series 326
- 314 i Series / iX Series 328
- 9.10 WHM Option 331
- 10. Error Messages 334
- 322 i Series / iX Series 336
- 324 i Series / iX Series 338
- Table 10-1: Error Messages 338
- 11. Index 339
Relacionado con productos y manuales para Grabadores de vídeo digital (dvr) Crest Electronics CDVS-7000
(30 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales